英语翻译1.Pull your cartridge or cartridges out of the printer a

英语翻译
1.Pull your cartridge or cartridges out of the printer and face them as shown.Note:You can reset just one cartridge,or both at the same time with this procedure.
2.Place a piece of tape so that it just covers the top 4 contacts on the top left side of the contact area as shown.
3.Reinsert the cartridges into the printer with the tape in place.
4.Close the lid and wait about 5 seconds.
5.Open the lid and wait for the printer to give the cartridges back to you.Note:The printer may take time to do this,and may flash to show there is an error with your cartridges.This is normal.
6.Remove the cartridges again and move the tape to the other side as shown in the lower pictures.
7.Reinsert the cartridges into the printer with the tape in place.
8.Close the lid and wait about 5 seconds.
9.Open the lid and wait for the printer to give the cartridges back to you.Note:The printer may flash to show there is an error with your cartridges again.This is normal.
10.Remove the cartridges and remove all the tape.Be sure the contacts are clean.
11.Place the cartridges back into the printer.They should now read 100% full.If not,redo the procedure,but only cover the top 3 contacts.If they still do not show as full,repeat,but only cover the top 2 contacts.
Three Cartridge Method
On some models the above procedure won't work,and you'll have to fool the printer by keeping three cartridges on hand
(these cartridges can be old,empty cartridges).This works because the printer only remembers the last TWO cartridges which were in it.The procedure is as follows:
•Cart #1 (empty) is removed for refilling
•Cart #2 is installed
•Cart #2 is removed
•Cart #3 is installed
•Cart #3 is removed
•Cart #1 (refilled) is installed.The printer now thinks that the filled cart is new.

1.把你的墨盒或盒式打印机和面对它们.如图所示.注:您可以将只是一个装,或两者同时采用这种方法.
　　2.放置一张胶带,所以它只涵盖了前4名联系人顶部左边的接触面积,如图所示.
　　3.复验盒式磁带到打印机和在适当的位置.
　　4.合上盖子,等了大约5秒.
　　5.打开盖子,等待打印机的墨盒回给你.注:打印机可以花时间去做这件事,可以闪光显示有错误与你的子弹.这是正常的.
　　6.拆卸盒式磁带又搬到河的另一边,如图较低的照片.
　　7.复验盒式磁带到打印机和在适当的位置.
　　8.合上盖子,等了大约5秒.
　　9.打开盖子,等待打印机的墨盒回给你.注:打印机也许闪光显示有错误和你再次墨盒.这是正常的.
　　10.拆卸盒式磁带和移除所有.可以肯定的是接触是干净的.
　　11分.将墨盒回打印机.他们现在应该读达到100%的圆满!如果不是,重复这个过程,但只覆盖了前三名的接触.如果他们还不显示,重复,但只有完全覆盖了前两接触.
　　三筒法
　　在某些型号上述程序行不通,你得傻瓜打印机墨盒上保持3手
　　这些子弹会老,空墨盒).这是因为打印机只记得上次两盒出来.这个程序如下:
　　车# 1(空•被移走,提高生产效率
　　2号安装•购物车
　　2号被•购物车
　　•推车# 3安装
　　•推车# 3被删除
　　(续•推车# 1)安装.现在认为打印机的车是新的充满.